Exterior Paint Guide to Choose, Prep & Apply (Step by Step)

A good exterior paint job protects your home from rain, sun, and rot, and it’s also one of the biggest curb-appeal upgrades you can make. It’s easy to get wrong, though. Most failures, like peeling, blistering, and chalky fade, come from skipped prep or bad timing, not cheap paint. This guide shows you how to choose the right paint, prepare the surface, and apply it the way pros do.

Check Your Home’s Age and Surface First

If your house was built before 1978, the old paint may contain lead. Don’t sand, scrape, or power wash it until you’ve tested it with a lead test kit or a lab. Under EPA rules, contractors working on these homes must be lead-safe certified. If you do the work yourself, follow lead-safe habits: cover the ground with plastic sheeting, scrape wet, use a HEPA vacuum, and never dry sand or burn old paint. Keep kids and pets away during the job.

Choose the Right Paint

For nearly every home, pick a 100% acrylic latex exterior paint. It stays flexible as siding expands and shrinks with the weather, so it resists cracking and peeling better than cheaper vinyl-acrylic blends. It also resists mildew and sun damage and cleans up with water. Oil-based paint is rarely needed today. If your trim was painted with oil, you can usually go over it with latex after cleaning, sanding, and applying a bonding primer.

Sheen matters outside, too. Use flat or low-sheen paint on siding, since it hides flaws on uneven walls. Satin also works well and sheds dirt a bit better. Use semi-gloss on trim, shutters, and doors because it’s harder and easier to wipe clean. A high-gloss finish suits a front door that you want to stand out.

Premium exterior paint costs more, often $40 to $80 a gallon, but it holds color longer and can last years beyond a budget can. Look for labels that mention UV protection and mildew resistance, and be careful with “paint and primer in one” claims. That formula won’t fix bare wood or stains. Your climate counts. In hot, sunny areas, choose a fade-resistant formula. In humid or shady areas, choose one with strong mildew protection.

Pick a Color That Lasts

Sunlight slowly fades every color, and deep, bold shades like red, navy, and bright green fade the fastest. If you have vinyl siding, there’s an extra rule most guides skip: dark colors absorb heat and can warp vinyl. Choose a “vinyl-safe” color, which usually means a light reflectance value (LRV) of about 55 or higher. The LRV is printed on many swatches or listed on the brand’s website.

Match your color to things you can’t change, like the roof, brick, stone, and driveway. Then test it properly. Paint a large sample directly on the house, in both a sunny spot and a shaded spot, and look at it in the morning, at noon, and in the evening. Colors almost always look lighter and brighter outside than on a small chip.

Prep the Surface (The Step That Decides How Long It Lasts)

  1.     Wash it. Use a pressure washer on a low setting, around 1,500 psi for wood, with a wide fan tip held at least 12 inches from the wall. Too much pressure gouges wood and forces water behind siding. For mildew, use a mildew cleaner or a mix of one part household bleach to three parts water. Wear eye protection and gloves, then rinse well and protect nearby plants.
  2.     Let it dry. This is a big miss in many guides. Wait at least 24 to 48 hours after washing. For wood, a moisture meter should read below 15 percent. Painting damp siding traps water and causes blisters later.
  3.     Do the chalk test. Rub your hand across the siding. If white powder comes off, the old paint is chalking. Wash it off, and use a bonding primer so the new paint can grip.
  4.     Do the tape test. Press painter’s tape firmly onto the old paint, then rip it off. If paint comes with it, scrape and sand more before going on.
  5.     The scrape, sand, and repair. Remove any loose or peeling paint and sand the edges smooth so the old patches don’t show through. Replace the rotted wood instead of painting over it, since the paint won’t stop the rot.
  6.     Caulk the gaps. Use a high-quality exterior caulk around windows, doors, and trim joints. Don’t caulk the bottom edge of lap siding or any weep holes, because they let trapped moisture escape.
  7.     Prime where needed. Prime bare wood, stains, rust, and patches. Cedar and redwood can bleed brown tannin stains through regular paint, so use a stain-blocking primer on them. Spot-prime small areas, but prime the whole wall if you’re changing from a dark color to a light one.

Apply the Paint Step by Step

  • Watch the weather. Most exterior paints go on best when both the air and surface are between 50°F and 90°F. Check your can, since some formulas allow lower temperatures. Skip days with rain in the forecast, strong wind, or heavy dew. Another detail competitors skip: avoid painting when the surface temperature is within 5°F of the dew point, because moisture can form on the wall and hurt adhesion. Also avoid painting a wall in direct, hot sun. It dries too fast and can leave lap marks.
  • Work top to bottom. Start with eaves and soffits, then siding, then trim, windows, and doors. Follow the shade around the house throughout the day.
  • Choose your tools. A sprayer covers large areas fast, but it needs careful masking and works best with back-brushing, which means brushing or rolling right after spraying to push paint into the surface. For smooth siding, use a 3/8-inch nap roller. For the rough surfaces like stucco, use a 3/4-inch or thicker nap. A 2.5-inch angled brush is perfect for trim and edges.
  • Keep a wet edge. Paint one section at a time, such as a few boards from end to end. If paint starts to dry before you blend the next stroke, you’ll see lap marks.
  • Apply two coats. Follow the can for recoat time, which is often about 4 hours. Two thin coats look better and last longer than one thick coat.
  • Finish the details. Paint trim and doors last. Remove the hardware when you can, and keep doors open until they’re dry so they don’t stick.

How Much Paint You’ll Need

One gallon covers about 250 to 400 square feet, and rough surfaces like stucco and brick need more. Measure each wall, subtract windows and doors, and plan on two coats. Mix all your paint together in a large bucket first, a trick pros call boxing, so the color stays consistent across the house.

Final Thoughts

Great exterior paint starts before the first stroke. Test for lead on older homes, choose a 100% acrylic paint in a color that suits your siding, prep until the surface is clean, dry, and sound, and paint in good weather. Do those things, and your finish will look sharp and protect your home for years. See more

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top